Status
Conditions
About
Infectious diseases pose a threat to the life of individuals worldwide. The pandemic has highlighted the need to develop an innovative and cost- effective large population-based screening methodology. The investigators propose a two-fold improvement barcode-labeled testing strategy specifically for pooled samples. This platform combines isothermal amplification and real-time electrochemical detection; electroactive modified loop probes will be used in the amplification step for barcode readout. This method enables four samples pooled detection at the same time. This platform will be integrated into a disposable microfluidic chip that allows minimal human intervention during the process to realize a massively parallel screening platform for infectious disease pathogens.
Objectives
Full description
Rapid host-to-host transmissions coupled with the ease of international travel has led to epidemics such as H5N1, H5N5, SARS, and, most recently, the COVID-19 pandemic. Traditional epidemic control measures, such as contact tracing and physical isolation, are paramount to mitigate the extent of disease spread at the early stage of the pandemic and these strategies depend on the accuracy and speed of diagnosing suspected patients.
Now the gold standard for pathogen detection is nucleic acid detection via polymerase chain reaction (PCR). However, this strategy is limited by the turnaround time, expensive PCR machine, and potential number of infections. Thus, other isothermal amplification methods are often used to circumvent the need for extra instrumentation and speed up the whole detection procedure.
One approach to improve infectious disease screening efficiency is the popular Dorfman testing, where samples are pooled together and tested at the same time to reduce the total number of tests performed. However, the Dorfman testing is limited to low prevalence population and has reduced sensitivity; Barcoding strategy has also been introduced to solve pooling sample test. In 2020, Schmid-Burk and his colleagues combined LAMP and barcoding which successfully developed COVID-19 from 100,000 pooled samples. However, the need of a expensive next-generation sequencer limits its widespread use.
Methods
The proposed platform aims at development of a multistep process in one device, and the capability of identifying the source of positive signals from pooled samples. The proposed design will take advantage of a barcoding strategy to tag multiple sources of analytes prior to pooling, a combination of isothermal amplification and sequence-specific electrochemical detection, and the integration of several steps in one simple device. The research project methodology will be divided into three parts.
(i) To develop an isothermal amplification method and real-time detection using electroactive-labelled loop oligonucleotide probes
The investigators have recently conceptualized a method, for which the investigators have filed a US provisional patent protection. This new technique performs the isothermal amplification and electrochemical detection of amplicons simultaneously based on Loop-mediated isothermal amplification (LAMP). The proposed scheme involves a one-pot amplification and detection system in which an electrochemical reporter is attached to one of the primers and a nicking enzyme is added to cleave the reporter only when amplification occurs. In one reaction, a template DNA is designed to have two pairs of primer binding sites: an outer pair of forward and backward primers (FP and BP) and an inner pair of primers, namely, an electrochemically labeled loop probe (LP) and an assistant probe (AP). The FP and LP bind to the same strand of the double-stranded DNA (dsDNA) template while the BP and AP bind to the opposite strand. The LP contains an electroactive label at the 5' end and a 3' overhanging segment complementary to the target DNA sequence. The stem region contains the recognition sequence of a nicking enzyme, but a mismatch is introduced to the last nucleotide so that it will not be cleaved without the presence of the target DNA. The start of the reaction is similar to ordinary LAMP, a double-loop amplicon can be produced, and the reaction can come into the double loop amplification stage. Each of the double-loop amplicons can be regarded as a signal amplification unit. Once the labeled LP is combined with the amplicon and form a cleavage site that can be recognized by the nick enzyme, an electroactive label can be released, and an electrochemical signal will be generated. The preliminary results indicate that the strategy is able to detect up to 0.1 fg/μL, corresponding to around 10 copies/μL of the input DNA, by using a methylene blue electroactive reporter on four-array screen-printed carbon electrodes (SPCEs) within 30 min. The succeeding steps include incorporating a reverse transcription step for the detection of RNA samples and testing the system in complex matrices to mimic actual biological fluids.
(ii) To design a molecular strategy to barcode four individual samples so that they can be pooled together and to simultaneously amplify and identify the positive individual, if any, from the pooled sample.
By designing four barcode sequences, the investigators are able to construct tagged cDNA products through reverse transcription by BST enzyme. Thermolabile exonuclease I is added to digest unreacted single strand barcode primers. In addition, the cDNA-RNA duplex product is digested by RNase H to yield a single-stranded cDNA (ID-template).The pooled mixture of ID-templates is amplified through the same process described in the previous section. Only those samples with the RNA virus will generate positive electrochemical signals.
In this part, the investigators will use synthesis virus RNA or commercial extracted virus total RNA as a detection template. The spiked samples can be mocked by mixing with human deep throat saliva or nasopharyngeal swabs from healthy volunteers.
(iii) To fabricate a microfluidic device to integrate the sample processor and barcoding module with the nucleic acid amplification and detection step for large-scale population screening
In this project, the investigators design a simple and easy-to-use microfluidic pen-like device that integrates the steps of sample preparation, barcoding, and amplification and detection. It uses piston propulsion to provide power to push the sample into different chambers. First, the mock samples are added into a sample loading chamber where the lysis buffer is stored. A mixture of surfactin, SDS, and ethanol allows the rapid extraction of viral nucleic acid, which is then injected down to the identification chamber containing the freeze-dried BST polymerase and ID-tag primer mixture. The temperature will remain at 37 °C-50°C for reverse transcription. Then, the sample is injected to the chamber containing thermolabile exonuclease I. The heating block is then set to 65 °C for 5 min to deactivate the enzyme. Thereafter, the four samples are pooled together and injected into an electrochemical detection chip below the microfluidic pen. Each chip contains four sets of primers and LPs with different electroactive reporters with non-overlapping redox potentials to trigger the amplification reaction in the presence of respective participant's ID sequences.
The detection chamber sits atop a multichannel electrochemical workstation, which consists of a connection port between the electrochemical sensor and detector, a circuit board, and a power line for external display. The circuit board is mainly composed of a microcontroller unit, a digital-to-analog converter, and a potentiostat module to allow for differential pulse voltammetry analysis and simultaneously obtain the signals from an array of electrodes and thereby detect a total of 100 samples.
(iv) To validate the performance of the prototype using a clinical specimen and benchmark it against the detection data from commercially available testing equipment.
The proposed method of pooled sample testing will be compared with the gold standard RT-PCR test in terms of sensitivity, specificity, positive predictive value, negative predictive value, and accuracy. After demonstrating the validity of the results obtained from the proposed pooling strategy, the investigators will then explore the possibility of using saliva and mouth gargle samples in lieu of the nasopharyngeal swabs. Patients will be recruited from the Prince of Wales Hospital for collection of respiratory samples to determine the accuracy of this device.
A. Study procedures
B. Laboratory procedures and data analyses
Study conduct
This study will be conducted in accordance with the Declaration of Helsinki.
Enrollment
Sex
Ages
Volunteers
Inclusion criteria
Exclusion criteria
200 participants in 2 patient groups
Loading...
Central trial contact
Catherine Cheung
Data sourced from clinicaltrials.gov
Clinical trials
Research sites
Resources
Legal